Engines : Jaguar AJ-V8

Taking Jaguar forward into the 21st century inevitably meant weaning it off its love affair with the straight-six, and taking the company in a whole new V8-powered direction. The AJ-V8 engine was the result of this radical thinking.

Ralph Hosier tells the story of its birth…


A change in direction…

There was a time when ‘Jaguar’ and ‘V8’ could not be uttered in the same breath, which is odd when you consider the majesty of the Daimler 2.5- and 4.5-litre V8s used since the 1960s. However, by the end of the 1980s, it was becoming clear that the weight of the gorgeous Jaguar V12 was just too much, plus its enormous physical size was hampering car design, particularly for crash performance where you need some crumple zone rather than solid engine.

The engine was revolutionary in the 1960s, but in the 1980s the labour intensive assembly and expensive parts were costing the company more than it was making. For the last years of the XJS, the V12 was not even on the official brochures, it was only its legend that was keeping sales alive. The AJ6 and AJ16 six-cylinder engines were making almost the same power and saved about 120kg which made a huge difference to the cars handling – but even this engine was showing its age.

New shorter engines were needed in order to allow sufficient room for an effective crumple zone. The engines needed to warm up more quickly, for both customer comfort and the ever-tightening emissions regulations. This required more precise cooling in the heads and block plus the use of considerably less metal. The piston ring system needed to control the oil much more accurately and piston friction had to be lowered. Indeed, friction throughout the engine needed to be reduced to meet the fuel economy targets and emissions targets.

With these issues in mind, a number of alternatives were looked at including a V12-derived V6 with the lost power being returned by using a brace of turbos. Another V6, an Orbital two-stroke engine which gave the same number of power strokes per rev as the old V12 engine, was looked at but oil control and refinement never quite met the targets. They even looked at a number of engines from other companies, which could be bought in without the huge cost of developing their own engine.

During the BL days there had been some discussion of using the Buick-derived Rover V8, which had substantial advantages in terms of weight (in fact it weighed half as much as the V12), cost and size. Unfortunately, most of the advantage came from the fact that it was relatively thin walled and so suffered in refinement a little. But in reality this could have been developed out, as was the case in the final fling of the Rover V8 inside the P38a Range Rovers.

However, that venerable V8 was itself a relic of the 1960s and ultimately suffered from the same issues as the old Jaguar engines, in terms of efficiency and emissions. It also struggled to meet the power demands of modern cars, the 4.6-litre version only putting out 220bhp.

A new design decision

That’s why, in the late 1980s, the bold decision was made to design a completely new Jaguar engine, one that would meet the forthcoming challenges of regulations and customer expectations. Originally code named the AJ12, the project used a single cylinder research engine to examine a number of different combustion chamber, cylinder head/port and cam options. This data showed that a 500cc cylinder with 26 degree ports and a four-valve configuration gave the best economy and performance for Jaguar applications.

Although AJ12 never resulted in a physical engine, the data was used to study a modular engine design, concentrating on a 4.0-litre eight-cylinder and a 3.0-litre six-cylinder, but also looking at a 2-litre four-cylinder, a 5-litre 10-cylinder and a 6-litre 12-cylinder engine. This would require some rather sophisticated machinery to be able to make all those variants, sharing common components such as piston and valves but little else. As the analysis data grew, it became clear that the complexity of doing all those variants would be crippling, so it was decided to concentrate on six, eight and 12-cylinder Vee-engines. Thus the project now became known as AJ26, 26 being the sum of six, eight and 12.

However, this would be hugely expensive, the fuel bill alone for testing engines runs into millions of pounds per year. At this time Jaguar was privately owned and, as such, there was simply not enough spare cash to invest in new products. What was needed was an owner who could suffer the financial hit in the long period between investment and return.

The Ford Factor

When Ford became interested in buying Jaguar, it was only natural to see if one of its many engines would fit the bill. Indeed, it was not uncommon for Jaguar owners in the USA to retro fit a Yank V8 so there was some precedence for this already.

Work had, though, already started on the fledgling Jaguar V8 and the Whitley team, lead by Dave Shutzpack, were passionate about seeing it through, they had looked at all the requirements and designed something that would give the legendary levels of Jaguar refinement and powerful whilst being small, light and efficient. But there would be a long road to go from a concept to a fully customer ready production engine. Typically, it takes around seven years – that’s a long time to ask an investor to wait for a return.

Ford looked at the arguments for both Ford engines and for the new Jaguar engines and, after all the data was analysed and the requirements understood, they decided to invest the millions needed by Jaguar to make their own new engine. However, this would be dedicated tooling for just the V8, all other variants were not to be.

The first year had been largely given over to defining the requirements, the specifications for each part of the engine such as how much heat goes into the coolant and the oil, how much force is needed to turn the engine over, valve train stiffness, noise levels as well as the major things like the power and torque levels.

This had lead to the basic design, this was put into the new computers and virtual tests run to establish the best coolant flow paths, the best inlet and exhaust port shape, the cam profiles and such. A huge amount of data was produced and analysed, without making a single engine. That was somewhat different to the early days of the V12 when development was a matter of calculated guess work and then lots of test engines proving it all out.

The calculation gave most of the answers, but some elements still required real-world testing. To this end, some elements of the new engine were experimented on in isolation, using a current production ‘slave’ engine as a base, giving rise to some odd reports in the press of the new engine being based on this, that and the other engine. For example, in order to try different bore and stroke combinations on the single cylinder rig, the engineers looked about for existing parts from all sorts of manufacturers, at one point it was using a Peugeot piston and a Mazda con rod!

V8 running

The first V8 engines were run on test beds in late 1989 and the first car to receive one was an XJ-S – in fact, one of the cars that had just finished being used to evaluate the twin turbo AJ16. As is always the way with the first ever engine installation, nothing fits, mounts, hoses, air intake and exhaust manifolds all had to be fabricated for the job. Steve, one of the mechanics on the job, recalls ‘they gave me a bag full of exhaust tube and various bends and told me to get on with it’. At the end of 1990, after a couple of weeks of trial and error fitting work the first 4-litre V8 Jaguar burbled into life and was universally admired by the small select audience of management privileged enough to see it, particularly in America which was a crucial market.

It weighed about the same as the old six-cylinder but had more power and a greater spread of torque, thanks to the new variable cam timing system. However, there was a small problem, it didn’t sound like a ‘Jaguar’. Although very appealing, the V8 burble sounded like any normal mid-size car in the USA and part of the Jaguar magic was the very high levels of refinement and quietness. Sound is such an emotive thing and much debate was had as to what the new engine should sound like, eventually the decision was made to make it quiet and an enormous amount of work went into designing complex intake and exhaust systems. It is interesting to note how this has changed now such that the current XKR even has a device built into the bulkhead to help you hear the engine’s magnificent growl.

The first car I drove with the new V8 was an XJ40 in about 1993 at the Ford Research Centre in Dunton, Essex. The car was based on the XJ12 body, code named XJ81, which had completely new metal work in front of the bulkhead in order to accept a vee engine. The car was bristling with new technology, it had one of the first electronic throttle systems and this particular car had a manual gearbox but with an automatic clutch. As you shifted gear, the systems would move the throttle and clutch so as to give you smooth gear shifts. It was marvellous to drive but ultimately it was easier to just use one of the excellent ZF five-speed auto gearboxes instead.

It’s interesting to note how Jaguar has had a history of technological innovation, and how right from the start how Jaguar was showing Ford new things. In return Ford showed Jaguar how to massively improve production processes, improving quality and reducing costs.

As the engine developed, the early tunes were used to check and refine the basic performance and emissions characteristics. Then cars were used to tune the transient response, that is to say how the engine responds to acceleration, deceleration and gear shifts. This is always a very difficult balance between good drivability and good emissions, a slightly rich fuelling on acceleration give very good drivability but will fail emission completely on hydrocarbons alone.

Part of the solution was to ensure the automatic gearbox control system ‘talked’ to the engine control system. This kept the throttle, fuel and spark precisely in tune with the change in engine speed during the shift, allowing the engine to anticipate the changes rather than have to react to them after the fact.

After the engine had received a good stable tune, it was time to test it in all the harsh climates it would face in the real world. Traditionally, this involves driving it in the Arctic and in the deserts of Arizona or Africa. But now tests could also be done in Ford’s climatic test chambers which drastically cuts down the development time and expense. As well as cold and hot climate tests, the new cars had to be tested in extremes of damp to check the corrosion resistance of the components and all the wiring. Then there is the rough road testing, both on a specially-prepared test track with a range of harsh surfaces, and on shake rigs where computer controlled hydraulic rams try to shake the car to pieces. In short, a lifetime of use and abuse is concentrated into a matter of months. By the end of 1994 a huge amount of data had been produced and all the necessary changes had been made, the results were looking very good indeed.

After this year of climate and durability tests, the final tweaks could be made and then it was time to start running the cars at Government-approved test centres to get the various certifications needed to sell a new car. At the same time further tests were re-run in house just to confirm that the final version was working as expected.

In parallel to all this development, the production plant was tooling up. First prototype tooling is made and the whole assembly process is tested, any special tools or assembly methods are identified and the first set of people are trained. The first few test cars were built this way, as were the cars eventually used for the journalists to drive at the launch in 1995.

The cost of production tooling is huge, the Bridgend AJ-V8 plant cost Ford £125 million. So it was vital to be certain that everything was right before the orders were placed, this could only happen when all the test data was in and all the tweaks had been tested. This is still true today and is one of the reasons it takes so long to get a new idea into production.

So, in 1997, eight years after the project started, the first XK8s were sold with the all-new, entirely Jaguar, V8 engines. A new era had begun.

Keith Adams

Keith Adams

Editor and creator AROnline at AROnline
Created www.austin-rover.co.uk in 2001 and built it to become the world's foremost reference source for all things BMC, Leyland and Rover Group, before renaming it AROnline in 2007.

Is the Editor of the Parkers website and price guide, formerly editor of Classic Car Weekly, and launch editor/creator of Modern Clsssics magazine. Has contributed to various motoring titles including Octane, Practical Classics, Evo, Honest John, CAR magazine, Autocar, Pistonheads, Diesel Car, Practical Performance Car, Performance French Car, Car Mechanics, Jaguar World Monthly, MG Enthusiast, Modern MINI, Practical Classics, Fifth Gear Website, Radio 4, and the the Motoring Independent...

Likes 'conditionally challenged' motors and taking them on unfeasable adventures all across Europe.
Keith Adams

Latest posts by Keith Adams (see all)

Keith Adams

About the Author:

Created www.austin-rover.co.uk in 2001 and built it to become the world's foremost reference source for all things BMC, Leyland and Rover Group, before renaming it AROnline in 2007. Is the Editor of the Parkers website and price guide, formerly editor of Classic Car Weekly, and launch editor/creator of Modern Clsssics magazine. Has contributed to various motoring titles including Octane, Practical Classics, Evo, Honest John, CAR magazine, Autocar, Pistonheads, Diesel Car, Practical Performance Car, Performance French Car, Car Mechanics, Jaguar World Monthly, MG Enthusiast, Modern MINI, Practical Classics, Fifth Gear Website, Radio 4, and the the Motoring Independent... Likes 'conditionally challenged' motors and taking them on unfeasable adventures all across Europe.

18 Comments on "Engines : Jaguar AJ-V8"

Trackback | Comments RSS Feed

  1. maestrowoff says:

    I hadn’t realised that the original V8 engine was launched nearly 20 years ago!

    This also led to the closure of the Radford engine plant which made the 6 cylinder engines, I imagine back then that nobody imagined a brand new engine plant being opened in Wolverhampton by JLR!

    • Chucky deHammer says:

      Firstly, the plant is not ‘in Wolverhampton’. Pretty darned close to the place yes, but that’s it.

      Second, Jaguar has a pretty close association to Wolverhampton and the immediate area, so it’s not perhaps as surprising as you may think.

      • maestrowoff says:

        I wasn’t expressing surprise at the choice of Wolverhampton, but rather that after the Ford takeover and closure of Radford, nobody have predicted a new JLR engine plant!
        Apart from price and availability, Wolverhampton was chosen for its convenience in serving both the Midlands assembly lines, and the Halewood plant.

        • Chucky deHammer says:

          It’s not in Wolverhampton. Try again.

          • barry says:

            Wolverhampton, West Midlands

            Our flagship Engine Manufacturing Centre, opened in 2013, is one of the most cutting-edge facilities of its kind in the UK, employing nearly 1,400 people. It is the first time we have designed and specified our own British production facility. Manufacturing a family of all-new low-emission 4-cylinder Jaguar Land Rover petrol and diesel engines, the plant brings our engine supply back to our production doorstep, helping us to achieve our ambitions and drive our continued success across the globe.

            above from jaguar website, might be worth telling them it is not in Wolverhampton then.

  2. Steve J Somers says:

    Proud owner of 2001 Sovereign
    DIY enthusiast – (first car was a Vanden Plas 3litre in the 60s)

  3. M says:

    How about a really small vee 12.

    • christopher storey says:

      The smallest V12 I can recall was Ferrari’s initial attempt at a V 12 in the 166 of c.1950 . 12 X 166cc = 1992cc . I think the problem is that such small cylinders are poor from an emissions point of view and thus a repeat of one this size is unlikely to be feasible

  4. christopher storey says:

    I should also have added that the ratio of frictional and pumping losses to power obviously increases the smaller and the more cylinders you have

  5. Andy W says:

    Fantastic engine, still running great in my XK8.

    Has been a mainstay of the Jag range throughout the late 90s and early to mid 00s, appearing in the S-type, XJ8 and XK8, as well as the supercharged version of the engine in the R models. The engine was the one element of Jag’s model range that stood comparison with the V8s in equivalent BMWs and Mercs, even as the cars fell behind the pace in other areas.

  6. maestrowoff says:

    As an aside, a variant of the AJ-V8 was also built in America, for use in the Lincoln LS (the cousin of the S-type) and Ford Thunderbird

    Not in production for very long, but according to Wiki 250,000 were made, so quite significant in the context of the programme, and I imagine a contributor to making the AJ-V8 programme financially possible

    • Nate says:

      While the Executive Car segment was becoming less profitable for non-luxury marques such as Ford and Vauxhall in the late-90s, it is a shame the Lincoln LS never formed the basis of a Ford Scorpio replacement utilizing Ford’s New Edge design language (as well as potentially forming the basis of a new rear-wheel drive replacement for the Ford Cougar in the mold of the Ford Capri).

      Though it is likely the Jaguar S-Type which used the same Ford DEW98 platform as the Lincoln LS would then be almost as unfairly maligned as the Ford Mondeo/Cougar-based Jaguar X-Type.

      • maestrowoff says:

        The S-Type did still suffer a bit from the Ford connection, though if the styling and feel is good enough, nobody cares, e.g. the XF, Freelander 2 and especially the RR Evoque.

  7. David 3500 says:

    From a purely hypothetical perspective, I wish this engine had been offered in the Rover 75 completed with a more modern ZF transmission, as it certainly had the refinement and power to suit its character. I am guessing it was not considered on the grounds that a) it would not likely fit in the Rover 75’s engine bay, b) the significantly higher purchase cost over that of the Ford alternative, and c) Jaguar Cars possibly not wanting to offer it to another manufacturer.

    A great engine which is equally at home in a screaming, tyre-burning sports car, delivering effortless refinement and power in reserve in a luxury saloon and oodles of low torque in a luxury off-road vehicle. Too right I like it!

  8. Fraser Mitchell says:

    Nobody seems to have mentioned its two very serious design faults that too some time to correct, namely the Nikasil bores, and the exhaust timing chain tensioners. The latter took Ford two attempts to sort out. Many engines didn’t even make it through the warranty period. The later 4.2 engine is well sorted, though. Troubles do still arise, as the 5 litre engines have suffered water pump failures.

Have your say...