ADO and other development codes

The XC numbers

The XC numbers (signifying ‘experimental car’) were applied to projects headed up by Alec Issigonis at Longbridge. These cars (with the exception of XC9000) all went on to be developed into production cars.

Codename Details Dates Picture
XC9000 1.5 litre saloon
Forerunner to the XC9001 – rear wheel drive saloon, resembled a Citroën due to its elongated wheelbase.
Dev: 1956-1957
XC9001 1.5 litre saloon
Initially a front wheel drive XC9000, but restyled by Longbridge and Pininfarina. Renamed XC9005 in 1960.
Dev: 1958-1960
XC9002 BMC 1100/1300
Initially a scaled down XC9001, but later restyled by Pininfarina. Became known as ADO16 from around July 1959.
Dev: 1957-1959
XC9003 BMC Mini
Also known as the ADO15.
Dev: 1957-1959
XC9005 BMC 1800/2200
XC9001 refined in style and re-engined with the 1.8-litre version of the B-series engine. Became known as ADO17 from 1960.
Dev: 1960-1962

The ADO numbers

After the merger between Austin and Morris in 1952, all subsequent new cars in development were given ADO project numbers. ADO stood for ‘Austin Drawing Office’, and the fact that they referred to an Austin and not a Morris drawing office gives some clue as to where the loyalties of BMC chief Leonard Lord lay.

Following this list (based on material supplied by the archive department at the BMIHT) can be confusing because the project numbers were not always in numerical order. In some instances, this muddled system made sense (ADO15, 16 and 17, for instance), whereas at other times, it obviously did not!

For example, look at ADO77, 88 and 99: ADO77 seems logical enough, as it follows ADO73, 74, 75 and 76, but following that comes ADO88, which was cited by Charles Griffin as being so called because of its 88-inch wheelbase. Following that came the ADO99, which again, possessed a 99-inch wheelbase. Was this pattern coincidence or was it chosen because of its nice, cascading numerical pattern? At the time of writing (November 2008), we are still without an answer to this question.

Codename Details Dates Picture
ADO6 Austin Hire Car and Taxi
FL2, FL2D, FX4, FX4D – better known as the London “Black Cab”
Dev: 1956-1959
Prod: 1959-1971
ADO8 Austin A40 Farina
MkI: BMC’s first hatchback, styled by Pininfarina
Dev: 1956-1958
Prod: 1958-1961
ADO9 Farina ‘B’ models
B-series engined Farinas:
Austin A55 Cambridge MkII (ADO9A), Morris Oxford Series V (ADO9M), MG Magnette MkIII (ADO9G), Riley 4/68 (ADO9R), Wolseley 15/60 (ADO9W)
Dev: 1956-1958
Prod: 1958-1961
ADO10 Farina ‘C’ models
C-series engined Farinas:
Austin A99 Westminster and Wolseley 6/99
Dev: 1956-1959
Prod: 1959-1961
ADO12 Hydrostatic transmission
As installed in an Austin A35 prototype.
Dev: Mid-1950s
ADO13 Austin-Healey Sprite MkI
Otherwise known as the ‘Frog-eye’ Sprite
Dev: 1956-1958
Prod: 1958-1961
ADO14 Austin Maxi Dev: 1964-1969
Prod: 1969-1981
ADO15 BMC Mini MkI and MkII (Originally codenamed XC9003) Includes Wolseley Hornet and Riley Elf, but not the Cooper versions (ADO50) Dev: 1957-1959
Prod: 1959-1969
ADO16 BMC 1100/1300
(Originally codenamed XC9002) Includes all badge-engineered varieties.
Dev: 1957-1962
Prod: 1962-1974
ADO17 BMC 1800/2200
(Originally codenamed XC9005)
Includes all badge-engineered varieties.
Dev: 1958-1964
Prod: 1964-1975
ADO19 Austin Ant
Prototype off-roader, cancelled by Leyland so as not to interfere with Land
Rover sales.
Dev: 1967-1968
ADO20 Mini MkIII and Clubman
Significant revisions to bodyshell, including slightly larger doors with
concealed hinges and wind-up windows; also marked a return to rubber-cone suspension. Clubman and 1275GT lasted until 1980
Dev: 1968-1969
Prod: 1969-2000
ADO21 MGB replacement
Mid-engined sports car, styled by Harris Mann/Paul Hughes and powered by the E4 engine. Dropped in favour of the TR7.
Dev: 1969-1970
ADO22 Facelift and re-engineering of ADO16
Major redesign of ADO16, incorporating revised suspension and under-structure, and revised bodywork. Cancelled by British Leyland, in favour of ADO67.
Dev: 1967-1968
ADO23 MGB Dev: 1958-1962
Prod: 1962-1974
ADO24 Austin-Healey 4000
4-litre version of the Austin-Healey 3000, cancelled by British Leyland.
Dev: 1966-1968
ADO25 E6 engine
6-cylinder E-series power unit, as used in ADO17 (and its derivatives),
Antipodean Marinas and ADO71.
Dev: 1965-1972
Prod: 1972-1982
ADO26 Austin Healey 3000 MKIII Dev: 1961-1963
Prod: 1963-1968
ADO27 Austin and Morris 1800 Facelift
This appears to have started out as a major facelift of ADO17, but the project was cancelled at an early stage. Code was passed on to the X6 project (codenamed YDO19 in Australia).
Dev: 1968-1970
Prod: 1970-1975
Riley 1.5/Wolseley 1500 facelift
The earlier of two recorded ADO27 projects, this would have seen these Morris Minor-based cars treated to Farina-style rear fins, perhaps not unlike those of the Australian Morris Major Elite (pictured is a Series II Lancer/Major), which was itself based on these cars.
Dev: Early 1960s
ADO28 Morris Marina
Using A- and B-Series engines
Dev: 1968-1971
Prod: 1971-1980
ADO30 Austin-Healey replacement
Project was vetoed by Sir William Lyons as it would have competed with the Jaguar E-type.
Dev: 1966
ADO31 MGA 1600 Dev: 1958-1959
Prod: 1959-1961
ADO32 E4 engine
Four-cylinder OHC E-series engine, as used in the Maxi and Allegro, and
also in the Australian Morris 1500
Dev: 1965-1969
Prod: 1969-1981
ADO34 Mini-based MG roadster
There were at least two distinct ADO34 prototypes: a ‘Longbridge’ car, designed and built by Pininfarina (pictured) and an ‘Abingdon’ car, produced in-house at the MG factory.
Dev: 1960-1964
ADO35 Coupé version of ADO34
The car pictured is understood to be a development of the ‘Longbridge’ ADO34 (see above).
Dev: 1960-1964
ADO36 Austin-Healey versions of ADO34 and ADO35
The car pictured is based on the ‘Abingdon’ ADO34, and differs from it only in respect of its grille and badge.
Dev: 1960-1964
ADO37 Princess 3-litre
Based on the Austin A99 Westminster, as a replacement for the Austin
A105 Vanden Plas
. It was marketed as the “Vanden Plas Princess 3-litre” from 1960 onwards.
Dev: 1959
Prod: 1959-1968
ADO38 Revised Farina ‘B’ models
Austin A60 Cambridge, Morris Oxford Series VI, MG Magnette MkIV, Riley 4/72, Wolseley 16/60.
Dev: 1960-1961
Prod: 1961-1971
ADO39 Taxi
FX4 replacement, cancelled by British Leyland
Dev: 1967
ADO40 Austin Freeway and Wolseley 24/80 Mk I
Produced in Australia and fitted with B-Series Six-cylinder engine…
Prod: 1962-1964
ADO41 Austin Freeway Utility
Prototype still exists in Australia
ADO42 Austin-Healey Sprite MKII
Rebodied version of the MkI Sprite
Dev: 1960-1961
Prod: 1961-1964
ADO44 Austin A40 Farina MKII Dev: 1960-1961
Prod: 1961-1967
ADO46 Farina ‘B’ diesels
Only the Austin A60 Cambridge and Morris Oxford versions were offered in diesel form. Originally for export only, they became available in the UK
from 1962. The diesel Cambridge was withdrawn in 1968.
Dev: 1961
Prod: 1961-1971
ADO47 MG Midget MkI
Badge-engineered version of ADO41
Dev: 1961
Prod: 1961-1964
ADO49 Farina ‘B’ Pickup
Pick-up truck based on Riley version of ADO9/ADO38; built and sold in Argentina.
Prod: early 1960s
ADO50 Mini Cooper and Cooper S (ADO50S)
997 and 998cc – and 970, 1071 and 1275cc (ADO50S)
Dev: 1961
Prod: 1961-1971
ADO51 Austin-Healey 3000 MkIV
This was to have been a badge-engineered version of the MGC, but was cancelled at Donald Healey’s insistence.
Dev: 1962-1965
ADO52 MGC Dev: 1961-1967
Prod: 1967-1969
ADO53 Revised ADO10
Became the Austin A110 Westminster and Wolseley 6/110.
Dev: 1961
Prod: 1961-1968
ADO56 MG Sport (details yet to be confirmed)
This Mini-based coupé proposal was conceived by Alec Issigonis, and featured front-wheel drive and a transverse Mini-Cooper engine. It apparently came very close to entering production.
Dev: 1958-1959
ADO58 Joint BMC/Rolls-Royce coupé project
To have been based on a short wheelbase version of Bentley Burma (pictured), the forerunner to the 1965 T1. The car would have been built and marketed exclusively by BMC, using the F60 6-cylinder engine, but it never reached production.
Dev: early 1960s
ADO59 Morris Minor 1000 (1.1 litre)
1098cc A-series powered Morris Minor
Dev: 1962
Prod: 1962-1971
ADO61 Austin 3-litre
Replacement for ADO53
Dev: 1962-1967
Prod: 1967-1971
ADO66 Vanden Plas 4-Litre R Dev: 1964
Prod: 1964-1968
ADO67 Austin Allegro Dev: 1968-1973
Prod: 1973-1982
ADO68 Project Condor
ADO68/28-1: A very stylish Roy Haynes-styled 2-door coupé version of the Marina. Dev: 1969-1970
ADO68/28-2: Late in 1969, the Italian designer Michelotti was commissioned to produce a version of Condor. His proposal was then amended in-house at BLMC to become ADO68/28-2, which hints at the shape of the 2-door Marina. Dev: 1969-1970
ADO68/14: This version of Condor, designed by Harris Mann, was based on the Maxi. It’s not hard to think of this design as the starting point for ADO71. Dev: 1969-1970
ADO68/67: The other Condor proposal was all-too-obviously based on the Allegro. Like the other Condor prototypes, this car met with its fate when Brtish Leyland cancelled the project. Dev: 1969-1970
ADO69 Taxi
Replacement for FX4 – cancelled
Dev: 1970
ADO70 Michelotti Mini
Michelotti-styled coupé model, based on ADO20.
Dev: 1970
ADO71 18-22 series/Princess
Replacement for ADO17.
Dev: 1970-1975
Prod: 1975-1982
ADO73 Marina 2/Morris Ital
Originally intended as a front-end facelift, but became the O-series version
Dev: 1972-1978
Prod: 1978-1984
ADO74 Ant/Dragonfly/Ladybird
Supermini project shelved by John Barber.
Dev: 1972-1973
ADO75 MGB GT V8 Dev: 1971-1972
Prod: 1972-1974
ADO76 Revised MGBs
Replacement MGB – based on a Michelotti-styled base
Dev: 1972-1974
Prod: 1974-1980
ADO77 “New” Marina
RWD Ford Cortina rival, ‘merged’ with the SD2 project – and then became
TM-1.
Dev: 1972-1975
ADO88 Supermini
Metro predecessor, cancelled due to unfavourable results from customer clinics. Re-engineered to become LC8 (Austin Metro).
Dev: 1974-1978
ADO99 Family hatchback
Replacement for Allegro, after internal re-organisation and the death of
TM-1. Became the LC10/LM10 (Austin Maestro). Project instigated by Spen
King.
Dev: 1975-1977

YD Codes

BMC Australia had trodden their own evolutionary path, once left to run with the BMC range of cars, and from 1962 the Antipodean subsidiary decided to use their own code numbers to denote development of cars specific to them.

Codename Details Dates Picture
YDO1 Morris Major Elite
First production type
April 1962-1963
YDO2 Morris Major Elite
Prototype of YDO1 with raised turret to improve rear seat headroom – not produced
YDO3 Austin Freeway MkII / Wolseley 24/80 MkII
Based upon Farina-style YDO9 vehicles and fitted with 2433cc B-Series 6-cylinder engine (unique to Austin). Produced in Austin and Wolseley sedan form, and Austin Station Wagon version…
August 1964-1965
YDO4 Mini (Morris only)
Standard version with Australian wind-up windows, 848cc engine and rubber cone suspension
1965-1969
YDO5 Mini Deluxe (Morris only)
…with Australian wind-up windows, 998cc engine and Hydrolastic suspension.
Also includes the Morris Mini K with with 1098cc engine.
1965-1969
1969-71 (K models)
YDO6 Mini Cooper S (Morris only)
…with Australian wind-up windows, 1275cc and Hydrolastic suspension
YDO7 Morris Mini Moke
…with 10″ wheels.
1966-1968
YDO9 Morris Nomad
ADO16 style five-door hatchback designed at Longbridge in conjunction with Australian engineers. Fitted with E-Series 1500 engine with manual gearbox or A-Series 1275 engine with automatic transmission.
1969-1971
YDO10 Morris 1800 Utility
Pickup version of the Austin 1800 ‘Landcrab’.
YDO14 Austin X6 Tasman/Kimberley Ute
Proposed pick-up version of Austin X6 cars (number not used, or not proceeded with).
YDO15 Morris 1500 and 1300 sedan
Similar to British 1300s and fitted with E-Series 1500 manual or 1275 automatic…
1969-1971
YDO18 Mini Moke (Morris and Leyland versions)
Update of YDO7 to 13″ wheels and initially fitted with 1098 and 1275cc
engines. Last unts were 998cc to achieve emissions requirements.
1968-1973
YDO19 Austin Tasman/Kimberley MkI and MkII
Update of ADO17 with E-Series 6-cylinder in single- (Tasman) or twin-carb (Kimberley) form, featuring revised front and rear styling…
Nov 1970-Jun 1971
YDO21 Mini Clubman
Australian standard version. 998cc and rubber cone suspension. Initially marketed as a Morris, then a Leyland…
1971-1978
YDO22 Mini Clubman Super
Australian deluxe-type version. 998 and 1098cc. Initially Hydrolastic suspension,
reverting to rubber cone later.
1971-73 (Deluxe)
1973-78 (S)
YDO23 Mini Clubman GT
Australian version, 1275cc engine.
1971-1973
YDO24 Morris Marina/Leyland Marina
Sedan (four-door) and TC Coupe (two-door). Australian version using E-Series 1500 and 1750cc engines.
1972-1975
YDO25 Leyland Marina
Six-cylinder versions using the 2.6-litre E-Series engine.
1973-1975

Notes:
It is rumoured that YDO26, 27 and 28 were allocated to the P76 sedan, station wagon and Force 7 coupe respectively, but were not proceeded with as Lord Stokes decided on the P76 code name. YDO Numbers not used: YDO8, YDO11, YDO12, YDO13, YDO16, YDO17 and YDO20

Based on information compiled by Peter A Jones, Roger Foy and Tony Dingle.


LC and LM codes

To signify the new direction the company was heading following the Ryder report in March 1975, the single and integrated Leyland Cars division changed their way of naming upcoming new car projects. This new system was implemented to replace the “ADO” system employed by Austin-Morris, as well as the fractious and none-too established naming employed by the Specialist Division.

The “LC” prefix stood for Leyland Cars, whilst “LM” referred to Light Medium. The Light Medium division came about due to a marketing reshuffle at BL in the autumn of 1979, when the Specialist Division was disbanded. The Light Medium division did not last long, being replaced by Austin Rover in 1980.

The LM codes changed on a fairly regular basis, as the business and the company’s relationship with Honda changed, but this list represents those projects actively pursued by Austin Rover.


LC series

Codename Details Dates Picture
LC8 Austin Metro
Picked up the pieces of the ADO88 project, employing that cars understructure, engines and suspension. LC8 signified a smarter body style.
Dev: 1978-1980
Prod: 1980-1991
LC9 Triumph Acclaim
Also known as “Project Bounty” by BL.
Dev: 1979-1981
Prod: 1981-1984
LC10 Austin Maestro
Signified the BL phase of the mid-sized car development programme, formerly known as ADO99 (and renamed thus to break links with the “ADO” naming scheme). Also covered a saloon version which would eventually become the Austin Montego (LM11).
Dev: 1977-1980
LC12 Coupé Dev: 1978-1980
LC40 Jaguar saloon
Jaguar’s XJ40 renamed in 1977 to tie in with the rest of the “single integrated” Leyland line-up. Codename only briefly used, reverting to XJ40 in 1978.
Dev: 1972-1986
Prod: 1986-1994

LM series

Codename Details Dates Picture
LM10 Austin Maestro
Final development name for this car – in this period, the rear suspension was altered.
Dev: 1980-1982
Prod: 1982-1994
LM11 Austin Montego Dev: 1980-1983
Prod: 1983-1994
LM12 Coupé
2-door coupé based on the LM11 floorpan – intended to be badged as an MG and replace all MGs and TRs.
Dev: 1980-1981
LM14 Five-door hatchback
Hatchback rear end for the Montego – similar in execution to the contemporary Talbot Alpine, VW Passat. This was to have been a more upmarket car than the Montego, with no 1300cc version.
Dev: 1980-1981
LM15 Executive car
Rebodied SD1; dropped by management on the advice of Roy Axe in favour of the Rover-Honda XX.
Dev: 1980-1981
LM19 Austin Ambassador
Rebodied ADO71.
Dev: 1980-1981
Prod: 1981-1984

Notes:
According to different BL/Austin Rover corporate plans, there were also references made to the LM16 and LM17. LM16 was referred to variously as an open topped version of the LM12 or a hatchback version of LM15. LM17 was another code used in reference to an executive class car, but the rebodied SD-1 LM15 project was actually seriously evaluated.


Honda/Rover and MGR codes

Unlike the long running ADO series and the politically sensitive LM series, the more recent development codes never seemed to catch the public’s imagination in quite the same way.


Honda/Rover codes

Codename Details Dates Picture
HD9 Medium hatchback
Five-door version of the Honda Ballade/Triumph Acclaim – probably a Triumph badged version of the Honda Quintet. A version of HD9 was marketed in Australia as the Rover Quintet.
Dev: 1981
HD14 Small hatchback
Sub-Metro sized car, probably a version of the Honda City/Jazz.
Dev: 1980-1981
HD17 Executive car
The initial internal name for the Honda-Rover large car to replace the SD1-based LM15 project. Was renamed XX in 1982.
Dev: 1981
XX Rover 800
First Honda/Rover collaborative car – became the Rover 800. LWB and CCV versions were developed, but not produced.
Dev: 1982-1986
Prod: 1986-1991
HX Honda Legend
Honda version of the XX – became the Honda Legend.
Dev: 1982-1985
Prod: 1985-1990
YY Rover 214/216
Early part of the Rover 200 development programme, renamed AR8 in 1986.
Dev: 1985-1986
HY Honda Concerto
Honda version of YY.
Dev: 1985-1988
AR5 Rover 213/216 replacement
Scheduled for a 1989 launch, but was cancelled in favour of the Honda based AR8 (see below), which served as a replacement for both the Maestro and Rover 213/216.
Dev: 1984-1985
AR6 Metro replacement
All new supermini styled by Gerry McGovern and Roy Axe, incorporating K-Series engine and steel suspension. Abandoned when it became clear that there were not enough company funds to finance its development. Replaced by the R6 (see below).
Dev: 1984-1986
AR7 Maestro replacement
Engineered in-house and scheduled for a 1990 launch, this car was cancelled in 1985 in favour of the Honda-based AR8 (see below).
Dev: 1984-1985
AR8 Rover 214/216
Renamed version of the YY. Renamed R8 in 1988.
Dev: 1986-1988
AR9 Roverised Montego
Thought to be a rebodied, Roverised version of the Montego, using the M16 power unit, though the existence of this project has yet to be confirmed.
AR16 Sub-800 4-door saloon
Counterpart to the 5-door AR17, both of which were based on a shortened XX (Rover 800) platform.
Dev: 1984-1985
AR17 Sub-800 5-door hatchback
Counterpart to the 4-door AR16, both of which were based on a shortened XX (Rover 800) platform.
Dev: 1984-1985
SK1 Rover 600
Honda-engined models
Dev: 1989-1993
Prod: 1993-1998
SK2 Rover 600
Rover-engined models
Dev: 1989-1993
Prod: 1993-1998
SK3 Metro replacement
Honda-developed hatchback – developed specifically for Rover and would not have had a Honda badged counterpart; cancelled in favour of Project R3 (see below).
Dev: 1989-1991
HH-R Rover 400/45
Also known as Project Theta. The mid-term facelift that produced the 45 was called Project Oyster. See also X20, below.
NB: Development dates refer to the Honda Domani, the Japanese market-only saloon that the Rover 400/Concerto was based on.
Dev: 1990-1995
Prod: 1995-date
CB40 Land Rover Freelander Dev: 1992-1997
Prod: 1997-date

Rover/MG Rover codes

Codename Details Dates Picture
R3 Rover 200/25Intended Metro replacement (originally codenamed SK3) based on a shortened
R8 platform. Was taken upmarket into the “Escort” market by George
Simpson
. The mid-term facelift that produced the 25 was called Project
Jewel. See also X30, below.
Dev: 1991-1995Prod: 1995-date
R6 Rover Metro/100 series
Heavily revised Austin Metro, incorporating K-Series engine, PSA derived
R65 gearbox and front/rear interconnected hydragas suspension.
Dev: 1986-1989Prod: 1990-1997
R6X Rover Metro/100 series – alternative bodyNew styling proposal for the R6, as designed by David Saddington – would
have used no carryover parts for the exterior.
Dev: 1987Prod: N/A
R7 Small hatchbackShortened R8 platform would have been used as a basis for this small hatchback.
Styling theme established by R6X was carried over.
Dev: 1988
Prod: N/A
R8 Rover 214/216Renamed version of AR8; the R8 code was used from the end of 1986 right
through to the end of the project. The codenames Tex, Tomcat and Tracer
were used for the 400 Tourer, 200 Coupe and 200 Cabriolet versions respectively.
Dev: 1986-1989Prod: 1989-1995
R9 R8-based saloon
This car would have been a larger saloon model than the R8-based 400, sharing
only its front door skins. It was dropped in favour of a “Roverised” version
of the Honda Concerto saloon (the car that was eventually launched as the
400). The R9′s role would have been closer to that of the later Rover 600.
Dev: 1986-1987
R17 Rover 800MkIIHatchback version Dev: 1989-1991Prod: 1991-1998
R18 Rover 800MkIISaloon version Dev: 1989-1991Prod: 1991-1998
R30 Rover 25/45 replacement
Aborted hatchback, designed using much BMW thinking. Was planned to use
the Hamms Hall-built “NG” 4-cylinder engines and, the joint Chrysler engine
used in the MINI. Cancelled when BMW abandoned Rover.
Dev: 1996-1999
R40 Rover 75Briefly known as “RD1″ in the early days. See also Core, Isis and X10, below. Dev: 1993-1998Prod: 1998-2005
R59
R50
New MiniOriginally codenamed R59, the R50 designation was adopted in May 1996, when
Frank Stephenson’s proposal (itself codenamed “E50 2+2″) was adopted for
the body style. Car was retained and launched by BMW following the split.
Dev: 1993-2000
RD60 Rover 45 replacementControversial hatchback and saloon replacement for the Rover 45 range of
cars. Styling by Peter Stevens is supposed to echo that of the TCV concept
car. Chassis/floorpan modified versio of Rover 75/MG ZT
Dev: 2001-2005
X10 MG ZT Dev: 2000-2001
Prod: 2001-2005
X11 MG ZT-T Dev: 2000-2001
Prod: 2001-2005
X12 MG ZT V8 Dev: 2000-2003
Prod: 2003-2005
X20 MG ZS Dev: 2000-2001
Prod: 2001-date
X30 MG ZR Dev: 2000-2001
Prod: 2001-2005
X40 MG TF Dev: 2000-2001
Prod: 2002-2005
X60 MG Version of the RD60The hatchback based on the Rover 75 floorpan; will contain many TCV styling
influences
Dev: 2001-2005
X80 MG XPower SVRebodied and re-engineered Qvale Mangusta, styled by Peter Stevens and manufactured
in Italy.
Dev: 2001-2003Prod: 2003-2005
RD110 CityRover
Rebadged and lightly restyled Tata Indica
Dev: 2003-2004Prod: 2004-2005
RDX60
RDX130
Rover 45/MG ZS ReplacementMG Rover codename for MG and Rover ranges.
RDX30 Rover 25/MG ZRMG Rover codename for both ranges.
RDX20 Rover 45/MG ZS
MG Rover codename for both ranges.
RDX10 Rover 75/MG ZTMG Rover codename for both ranges.

Project codenames

Codename Details Dates Picture
Adder MGR V8
The project name for the MGB-based roadster which became the MGR V8. The prototype was also known as PR4 (see below).
Dev: 1989-1993
Prod: 1993-1995
Core Rover 75
The inital project name for the car that would become the Rover 75. At this time, it was one of a suite of three large-car projects (the others being Eric and Flagship) based on an all-new Rover platform.
Dev: 1993-1998
Prod: 1998-date
Eric Large avantgarde coupe
The third model in Rover’s inital project mid-1990s large-car programme (along with Core and Flagship), this would have been an executive-class coupe, apparently not unlike the Renault Avantime in concept. Like Flagship (below), it did not progress beyond the fibreglass model stage.
Dev: 1993-1994
Flagship Range-topping model
Part of Rover’s mid-1990s large-car programme (along with Core and Eric), and as the name suggests, this would have been a luxury saloon sitting above the 800 in the range; it was affectionately referred to within the company as “Flashpig”. Like Eric (above), it did not progress beyond the fibreglass model stage.
Dev: 1993-1994
Isis Rover 75
An old Morris model name, revived to refer to one incarnarnation of the car that would become the Rover 75. This codename was used between “Core” and “RD1″.
Dev: 1993-1998
Prod: 1998-date
Jewel Rover 25
Facelift of the R3 Rover 200 to bring it into line with Rover’s new 75-inspired family look.
Dev: 1998-1999
Prod: 1999-date
Oyster Rover 45
Facelift of the HH-R Rover 400 to bring it into line with Rover’s new 75-inspired family look.
Dev: 1998-1999
Prod: 1999-date
Pathfinder Soft-roader/SUV
Aborted high-bodied multi-purpose vehicle, using the Rover 800 floorpan. Evolved into the CB40 (Land Rover Freelander) project.
Dev: 1989-1992
Synchro Rover 600
See entries for SK1 and SK2, above.
Dev: 1989-1993
Prod: 1993-1998
Theta Rover 400/45
Alternative name for Project HH-R (above). See also X20.
Dev: 1990-1995
Prod: 1995-date
Tex Rover 400 Tourer
Developed as part of the R8 programme.
Dev: 1988-1992
Prod: 1994-1996
Tomcat Rover 200 Coupe
Developed as part of the R8 programme.
Dev: 1988-1992
Prod: 1993-1999
Tracer Rover 200 Cabriolet
Developed as part of the R8 programme.
Dev: 1988-1992
Prod: 1992-1999

Project Phoenix & the PR/PX codes

Codename Details Dates Picture
F-16 MG-F forerunner
Gerry McGovern-styled car with front-engined, front-wheel-drive configuration. This design marks the birth of the MG-F concept, as its shape was used to form the body panels for PR1, PR2 and PR3.
Dev: 1985-1989
PR1 MG-F forerunner
The first of three Phoenix prototypes, this car was built in steel by Motor Panels on Maestro underpinnings and used a front-mounted transverse 2.0 M16 engine.
Dev: 1989-1990
PR2 MG-F forerunner
The second Phoenix prototype was built by Reliant using the Scimitar SS1 as its basis, and had a Rover 3.9-litre V8 engine.
Dev: 1989-1990
PR3 MG-F forerunner
The third Phoenix prototype, built by ADC. This was the mid-engined design that was successful in being selected to be taken forward as the MG-F.
Dev: 1990
PR3/8300
Styling development of original PR3 exercise, produced by ADC in 1991 as part of the process of ‘productionising’ the design.
Dev: 1991
MG-F
Gerry McGovern sketched this final proposal for the PR3, giving the car much needed character, whilst also doing away with the need for troublesome and aerodynamically inefficient pop-up lights.
Dev: 1991-1995
Prod: 1995-date
PR4 MGR V8
This code was assigned to Project Adder, the MGB-based roadster which became the MGR V8 (see Project Adder, above).
Dev: 1989-1993
Prod: 1993-1995
DR2/PR5 Parallel MG-F proposal
This Roy Axe design was altogether bigger than the other PR-series cars, but like PR2, it had a front-mounted V8 and rear-wheel drive. It could potentially have becme an Austin-Healey if the marque had been revived.
Dev: 1990
PX1 Parallel MG-F proposal
A revival of the PR1 project, this car was based on front-engined, front-wheel-drive R17 (Rover 800) underpinnings. Was futher developed to become Adventurer-1 (pictured).
Dev: 1991
PX2 Parallel MG-F proposal
Related to PX1, but with a shortened wheelbase and retro-styling. Became Adventurer-2 (pictured).
Dev: 1991

Miscellaneous codes

Of course, in a company as wide ranging as British Leyland, many, many other projects were given their own names, as it was not until the 1980s that a centralised product design and planning system was set-up.

This page includes the one-off project names, plus some of the code series which existed within the individual companies prior to the various mergers.


BMC

Codename Details Dates Picture
9X New Mini
Issigonis-designed, OHC-engined hatchback to replace the Mini. 9X incorporated 850, 1000cc three door Mini-replacement hatchbacks and a further, extended 5-door version using 1200 and 1500c six-cylinder versions of the same OHC engine to replace ADO16.
Dev: 1967-68
Barrel Car New Mini
Longbridge-produced Mini facelift proposal – not linked to either the 9X or ADO74 projects. Publicised in the Jeff Daniels and Graham Robson books.
Dev: 1968

Rover P series

Codename Details Dates Picture
P1 ‘D-back’ Ten , Twelve and Fourteen saloons
(P1 Ten continued to end of 1937)Open Tourer Twelve and Fourteen models 1934-36
Prod: 1934-36
P2 Phase 1 (1936-40)
New Twelve, Fourteen and Sixteen, more rounded style, enclosed boot, in 6-light Saloon and 4-light Sports Saloon  versionsPhase 2 (1938-40)
New Ten in ‘scaled-down’ P2 Twelve  6-light style
Plus low-volume Ten 2-door Coupe and Twenty Sports Saloon

Phase 3 (1946-48)
Post-war Ten 6-light, Twelve, Fourteen and Sixteen in 6 and 4-light styles. ‘Export only’ Twelve Tourer

Prod: 1936-48
P3 Rover 60, 75. Prod: 1948-50
P4 ‘Cyclops’ 75, then 60, 75, 90, 105, 80, 100, 95, 110 Prod: 1949-64
P5 Three Litre (first monocoque Rover). Prod: 1958-67
P5B 3.5 litre version of the P5 (saloon and coupé). Dev: 1965-67
Prod: 1967-73
P6 2000, 2200 (base unit construction). Prod: 1963-77
P6B “Three Thousand Five” – 3.5 litre version of P6. Prod: 1966-76
P6BS Mid-engined sports car “Porsche eater” – development version. Dev: 1965-68
P7 5, 6 and V6 cylinder versions of P6 used in P8 development programme – never intended for production. Dev: 1962-74
P8 3.5, 4 and 4.4 litre versions of the P5 replacement. Axed by British Leyland at the point of going into production. Dev: 1963-71
P9 Productionised version of the P6BS. Dev: 1968-70
P10 Became known as the RT-1 and then SD1. Dev: 1969-71

Rover-Triumph

Codename Details Dates Picture
SD1 Rover 3500“SD” stands for Specialist Division Dev: 1970-76
Prod: 1976-86
SD2 Triumph Dolomite replacementSolihull designed 5-door hatchback, using 1.5 and 2-litre Triumph engines.
Merged with the ADO77 project in 1975.
Dev: 1971-75
SD3 Rover 213/216
Little-known code applied retrospectively by engineers for the range that
replaced the Triumph Acclaim. Apparently Honda had it in mind to use the
code SD2, until it was pointed out that that one had already been taken
(see above)…
Dev: 1982-84
SD5 Land-Rover replacementA proposed replacement for the traditional Land Rover… Dev: 1972-1974
Bravo Rover SD1 reskinLate 1970s proposal to relaunch the SD1 with new bodywork, in both 4- and
5-door forms. Plan was abandoned in favour of Project XX (Rover 800).
Dev: 1979-80
:

Austin-Morris

Codename Details Dates Picture
AM2 Metro saloon Dev: late 1970s

Triumph-Morris

Codename Details Dates Picture
TM1 Family saloon Dev: 1975

Triumph

Codename Details Dates Picture
Bullet Sportscar
Front engined, rear wheel drive, targa top, two seater sports car developed to replace the TR6 and GT6. Developed and federalised to produce the Triumph TR7.
Dev: 1969-70
Lynx Sportscar projects
Michelotti-styled coupe version of the Bullet Dev: 1969-71
Coupe version of the TR7/TR8 – failed to become production reality due to production interruption at Speke. Dev: 1973-77
Puma Executive car
Triumph replacement for the 2000/2500 models – was cancelled in favour of the Rover proposal, the Canley and Solihull teams joined forces and the joint replacement car became the SD1.
Dev: 1969-70
Keith Adams

About the Author:

AROnlineholic between 2001 and 2014 - editor of Classic Car Weekly, and all round car nut...

8 Comments on "ADO and other development codes"

Trackback | Comments RSS Feed

  1. Landyboy says:

    You could add R53 to the R50 entry, as this was the code name for the Cooper S version

  2. Dave Boon says:

    What a fantastic run of information. P6BS looked like an intersting vehicle. Never thought about or seen a Landcrab pickup. Brilliant. Keep the good work and the information coming.

    Dave B

  3. Ian Nicholls says:

    Did the original Range Rover have a ‘P’ code ?

  4. Michael Allen says:

    “Did the original Range Rover have a ‘P’ code?”
    No, it was simply known as the “100-inch Station Wagon”, referred to as “Road Rover” and designated “Velar” when the pilot run cars were sent out for testing.
    The second generation Range Rover’s P designation is an interesting one: P38. All sorts of speculation as to what it stood for, but the answer is quite unremarkable – it was the number of the Office in which it was designed!

  5. Will M says:

    There was a question raised recently on whether SD4 existed?

    Was it a cancelled project?
    An internal project?
    Engineering project?

  6. Kev says:

    Re 5: That’s not quite correct. The origin of ‘P38′ is a little more complicated:

    1) The body engineering for ‘P38′ was contracted out to MGA Developments Ltd, of Coventry. MGA gave the project a code name – Mustang. This was very quickly abbreviated to ‘P51′.

    2) In parallel, the Land Rover program team at Solihull was housed in Block 38 (adjacent to the famous ‘jungle track’).

    3) Eventually the ‘P51′ and ‘Block 38′ references became blended in to ‘P38′.

    (I was a Senior Engineer on the MGA team.)

  7. Very well researched information!
    I have seen other “ADO” lists and they have errors and omissions, yours is the best I have seen so far.
    Thanks for including the Australian “YD” codes, there is very little information about them elsewhere.
    Regards from Michael in Australia.
    P.S. Did the South African arm of BMC-Leyland have their own development codes?
    South Africa produced their own Wolseley 1000(ADO15)and Austin ADO16

Have your say...